An ordinary camera has a lens that makes an image on film. In a pinhole camera. A small hole replaces the lens. You can construct a pinhole camera using: • corrugated cardboard from a box, or stiff cardboard from the back of a pad of paper • black paper • black tape • a cartridge of 126 film* • aluminum foil • two large rubber bands • a ruler • a pencil • scissors • a sharp knife • a straight pin or sewing needle Making a pinhole camera The diagram shows the basic construction of a pinhole camera. The body of the camera is a cardboard box that is open at both ends.

To make this box, cut a rectangle of cardboard that measures 5 3/4 inches by 2 inches. Divide the long edge of the rectangle into four equal sections. Use your knife to score the cardboard along each of the lines. Fold the cardboard along the scores to make an open-ended box.

Learn how to make your very own pinhole camera to safely see a solar eclipse in action!

Before you tape the edges together to make a box, you need to make the interior black to minimize reflection of light within the camera. You can cut a piece of black paper and fold it to make a black lining for your box, or you can cover the inside surface of the cardboard with strips of black tape. You could also paint the inside flat black with spray paint or tempera. Now tape the edges together to make a box, and tape all the box's edges and corners to prevent light from leaking into the camera. Insert the box into the film cartridge as shown. It should fit tightly.

When you hold the open end of the box up to your eye, you shouldn't see any light leaking in where the box fits into the cartridge. To make the front of the camera, cut a rectangle of cardboard that measures about 1 3/4 by 3 inches. Cut a square hole that measures about 1/2 inch by 1/2 inch in the center of the rectangle. Line the inside of the front of the box with black paper or tape, leaving the hole open.

Tape a 1-inch square of aluminum foil over the square hole, and make a small pinhole in the center of the foil. When you aren't taking a picture, you need to cover the pinhole with black paper.

We made a shutter that slides into black paper guides. To ensure that no light can leak in, tape the box to the front with black tape.

Microcat hyundai dongle crack load. Fasten the camera to the cartridge with rubber bands, as shown. Taking photos with your pinhole camera Through the window in the back of the film cartridge, you'll see arrows.

Use a coin as shown in the diagram, turning it clockwise to advance the film in the direction of the arrows. Eventually, you'll see the frame number 1 through the window, the first in a series of 1's. Stop advancing the film when the third and fourth 1 in the series are both visible through the window.

Now you're ready to take a picture. To get a sharp photo, it's important to hold your pinhole camera steady To keep the camera steady. One of our staff suggested that you 'tape it to a brick.' He attached his pinhole camera to a tripod with rubber bands. This photo was taken with a pinhole camera. Using ASA 200 film in bright sunlight, we found that we got good pictures with exposure times varving from one to three seconds.

The ideal exposure time will depend on the size of your pinhole and the brightness of the day. Experiment with different exposure times, and you'll learn which times give the best results. After each photo. Advance the film until the third and fourth number in the series of frame numbers appear in the window. When you've finished the roll, you can take your film to a commercial photoprocessor for developing. * Kodak still has a limited supply of 126 cartridges. You can get them directly by calling the Kodak Info Center at 1-800-242-2424 x10.

They accept MasterCard and Visa only. If you buy directly from Kodak, you will be paying full retail prices. If you need a large quantity, contact a local dealer who can special order them at dealer cost and possible give you a discount.

Macro lenses for DSLR cameras often cost a small fortune, but their close-up shots are hard to resist. Luckily there's other alternatives. Using some clever tricks, you can transform basic kit lenses (that usually come with the camera) into incredible macro-shot lenses. Crafting carefully, you get an added bonus of a pinhole camera lens at the same time. Crisp microscope-like macro shots and dreamy pinhole shots are sure to impress others with your artistic talent.

Also crafting something useful from items that are usually considered trash is both eco-friendly and fun. Materials required: -Body Cap for the camera -A Can, either a tin can or a Pringles one, slightly larger diameter than the lens of the camera.

-A Sock, an expendable one. Tools required: -Compass for drawing circles of certain radius -Ruler or caliper -Adhesive tape, a kind on which you can draw thin lines on -Blu-tack -A needle, for making a tiny hole in sheet metal -Drill, or some other way of cutting plastic and metal -File, sanding paper or a grinding tip for the drill, for smoothing out rough cut surfaces -Pair of scissors -Protective eyewear, pictures are more fun if you still have your eyes -Protective gloves and/or hearing protection, depending on your method of cutting/finishing the can and body cap. First thing to do is to measure the inner diameter of the camera-side of the body cap. This determines the size of hole that is to be cut to bottom of the can. My Canon cap measured 48mm, you might want to check the measure yourself. Then draw a similar sized circle in a piece of paper and cut precisely along the circle to create a paper disk that fits on the inner side of the body cap nicely.